Most customers who buy screw air compressors often don’t pay much attention to the installation of screw air compressors. However, screw air compressors are very important during use. But once there is a small problem with the screw air compressor, it will affect the production of the entire factory. Therefore, companies will face a problem after purchasing screw air compressors-installation. Let me talk to you about how to install a screw air compressor. The installation process of a screw air compressor is roughly divided into the following steps:
1.When piping the main line, the pipeline must have a slope of 1°-2° to facilitate the discharge of condensed water in the pipeline. Secondly, the pipeline pressure drop must not exceed the set pressure.
2.The branch line is connected from the top of the main line to prevent the condensed water in the main line from flowing into the working machine. The air outlet pipeline of the OPPAIR screw air compressor should have a one-way valve.
3.When the screw air compressor is installed in series, a ball valve or automatic drain valve should be installed at the end of the main line to facilitate condensate discharge.
4. The main pipeline cannot be reduced arbitrarily. If the compresores de aire pipeline is reduced or enlarged, a tapered pipe must be used, otherwise there will be mixed flow at the joint, resulting in large pressure loss and affecting the service life of the pipeline.
5. It is recommended to use the following supporting equipment: air compressor + separator + air tank + front filter + dryer + rear filter + fine filter.
6. Try to reduce the use of elbows and various valves in the pipeline to reduce pressure loss.
7. It is recommended that the main pipeline surround the entire plant, and configure appropriate valves on the ring trunk line for maintenance and cutting.
This is the link provided by OPPAIR on how to connect the PM VSD or Fixed Speed screw air compressor and the air tank or the air dryer:
INSTALLATION/USE/MAINTENANCE GUIDE
1.When installing, pay attention to maintaining ventilation.
2.The power supply voltage must be consistent with the air compressor voltage, pls same with compressor nameplate,otherwise the air compressor will be burned out!
3.After connecting to power, compressor has phase sequence protection. lf the screen displays an incorrect phase sequence, swap any two of the three live wires and restart compressor to operate normally.
4.Check whether oil level of oil and gas barrel is normal. Oil level needs to be between upper and lower limits(When not started, oil level is higher than the upper limit, because after operation, oil level will drop. Oil level must not be lower than the lower line during operation). During operation, if the oil level is lower than the minimum oil level line, you need to stop and refuel oil.
5. There is a 3-5 minute start-up delay for air dryer/Adsorption dryer, Before starting compressor, start air
dryer/Adsorption dryer at least 5 minutes in advance. When shutting down, first turn off compressor, then turn off air dryer/Adsorption dryer.
6.Air tank needs to be drained regularly (Frequency of drainage depends on individual circumstances), every week, or every 2-3 days. Particularly humid places need to be drained every day. (There is rust in the drainage, which is normal)
7. When the gas consumption is low, the oil and gas barrel must be drained every day, otherwise it will cause the air end to rust.
8. It is best to keep compressor and dryer running for more than 1 hour each time. (Do not turn on and off frequently)
9. Do not adjust parameters at will. If you have any questions, please contact the dealer or manufacturer.
10. in dally use, pay attention to daily cleaning and dust blowing of the air compressor to avoid clogging of the air compressor and high temperature.1 1. When the maintenance time comes, the compressor will alarm in advance. The first warranty time of the compressor before August 2024 is 500 hours. After August 3, 2024, the first warranty time of the machine is.2000-3000 hours,and the subsequent warranty time is 2000-3000 hours.
MAINTENANCE PROCESS
A.Replaced: air filter, oil filter, oil separator, air compressor oil. (Note: Choose No.46 fully synthetic or semi-synthetic special air compressor oil.)
B.Find the consumables parameters on the controller, and adjust the oil filter usage time, air filter usage time, oil filter usage time, and air compressor oil usage time to 0. Then change the maximum usage time of the above to 3000.
C.Return to the main page, the alarm disappears, and it can be used normally
The above is OPPAIR' s view on how to install a screw air compressor. We hope it will be helpful for you when choosing a hava kompresr. Because each screw air compressor manufacturer has differences in production batches and models, when the screw air compressors has problems or needs maintenance and inspection, everyone should contact the rotary air compressor manufacturer so that the problems that the screw air kompresr always encounters in the production process can be easily solved.
OPPAIR screw air compressor manufacturer has an experienced production, installation, and after-sales team. Products include: industrial fixed speed rotary screw air compressors, laser cutting all in one air compressors, permanent magnet variable frequency(PM VSD) screw air compressors, two-stage low pressure Baosi/Hanbell air end screw air compressors, skid mounted laser cutting screw air compressor, diesel mobile series screw air compressor, two-stage high pressure screw air compressors and other series of products.
OPPAIR is looking for global agents, welcome to contact us for inquiries: WhatsApp: +86 14768192555
#Electric Rotary Screw air Compressor #Screw Air Compressor With Air Dryer #High Pressure Low Noise Two Stage Air Compressor Screw
Post time: Mar-11-2025